Outlining and Configuring Storage Control

Configuring Process-Oriented Storage Control

Objective

After completing this lesson, you will be able to describe and execute process-oriented storage control.

Process-Oriented Storage Control Basics

Determination of Deconsolidation

In the example, the system determined that deconsolidation was required based on the fact that the consolidation group determined from the putaway location for each product was different. The following figure shows this scenario:

A diagram illustrating how the system determines if deconsolidation is required based on the consolidation group and putaway location for different materials.

In this figure, for each material, the system determines a putaway strategy that determines the putaway bin location (St. Type-Section-Bin). The putaway location determines the activity area (bins are assigned to activity areas). A deconsolidation group is assigned to each activity area. If they are different for products in the same HU, the HU must go to deconsolidation.

Configuration Settings

Based on different processing requirements of the products in your warehouse, you define the process-oriented storage control as part of the configuration settings.

Generally, the approach to configuring process-oriented storage control is to first define the warehouse process steps that are applied to your products. You define External Process Steps, which are connected to an Internal Process Step (defined by SAP). The internal process steps cannot be altered or supplemented with your own. The following figure illustrates the external to internal process step assignment:

A diagram showing the mapping between external process steps defined by the customer and internal process steps defined by SAP in process-oriented storage control.

The storage process is a combination of individual external storage process steps, through which the product passes as part of its complex goods receipt or goods issue process. Storage processes are configured for each warehouse. You can configure a storage process in Customizing for SCM Extended Warehouse Management, in Extended Warehouse Management→Cross-Process Settings→Warehouse Task→Define Process-Oriented Storage Control.

You can assign process steps to a storage process only in a specific sequence.

For the putaway process, this is as follows (the list shows the internal process steps):

  1. Unload
  2. Count
  3. Deconsolidation
  4. Quality inspection
  5. Value-added service (VAS)
  6. Putaway

For the stock removal process, this is as follows:

  1. Remove from stock
  2. Value-added services (VAS)
  3. Pack
  4. Stage
  5. Load

Each storage process step represents a potential movement in the warehouse. The SAP EWM system uses logic related to the internal processes to determine whether a warehouse task will be or can be created.

The Auto WT setting on the process step determines whether the subsequent warehouse task will be created or not. If the Auto WT setting is not made, the warehouse task will have to be created manually.

Note

In most cases it will make sense to have the subsequent WT created automatically. A scenario where this might not be, is that after the Staging step, you want the Loading WT to be created manually, because that shall only happen once the truck for pickup has arrived.

The Prod/HU WT setting controls when during a putaway process the product warehouse task (which is the final process step during putaway) are to be created. In a picking process the first process step is always a product warehouse task, so it is not necessary to set this flag. The other process steps in the process use HU warehouse tasks.

The system uses the time-related entries in the process step to compute an estimate of the total processing time in Labor Management planning.

The external storage process step is also used to determine the destination location in the warehouse task generated by the step. You can either directly maintain a destination storage bin or use a rule-based determination. You can also enter a warehouse process type for the external step, which is used to create the corresponding WT.

Storage Process Determination

The storage process is determined depending on the direction of the warehouse request. For inbound movements, the storage process comes directly from the warehouse process type determined in the warehouse request. For outbound delivery orders, the storage process is part of the warehouse order creation rule (which is explained in a separate unit).

A flowchart illustrating the determination of storage processes for inbound deliveries via warehouse process types and for outbound delivery orders via warehouse order creation rules.

Summary

  • Manage complex warehouse movements by combining multiple process steps into a single storage process.
  • Execute process-oriented storage control (POSC) exclusively with handling units (HUs) by mapping external steps to internal SAP-defined steps.
  • Determine storage processes based on the warehouse request direction, using warehouse process types for inbound and warehouse order creation rules for outbound.

Configure Process-Oriented Storage Control